Antimony trifluoride

Antimony trifluoride
Structural formula
Structural formula
space-filling model
space-filling model
Unit cell
Unit cell
Unit cell of antimony trifluoride. The distorted-octahedral coordination of the fluorine relative to the antimony is visualized.
Unit cell of antimony trifluoride. The distorted-octahedral coordination of the fluorine relative to the antimony is visualized.
Names
Preferred IUPAC name
Antimony(III) fluoride
Systematic IUPAC name
Trifluorostibane
Other names
Trifluoroantimony
Identifiers
3D model (JSmol)
ChemSpider
ECHA InfoCard 100.029.099 Edit this at Wikidata
EC Number
  • 232-009-2
RTECS number
  • CC5150000
UNII
UN number UN 2923
  • InChI=1S/3FH.Sb/h3*1H;/q;;;+3/p-3 checkY
    Key: GUNJVIDCYZYFGV-UHFFFAOYSA-K checkY
  • InChI=1S/3FH.Sb/h3*1H;/q;;;+3/p-3
    Key: GUNJVIDCYZYFGV-UHFFFAOYSA-K
  • InChI=1/3FH.Sb/h3*1H;/q;;;+3/p-3
    Key: GUNJVIDCYZYFGV-DFZHHIFOAW
  • F[Sb](F)F
Properties
SbF3
Molar mass 178.76 g/mol
Appearance light gray to white crystals
Odor pungent
Density 4.379 g/cm3
Melting point 292 °C (558 °F; 565 K)
Boiling point 376 °C (709 °F; 649 K)
385 g/100 mL (0 °C)
443 g/100 mL (20 °C)
562 g/100 mL (30 °C)
Solubility soluble in methanol, acetone
insoluble in ammonia
-46.0·10−6 cm3/mol
Structure
Orthorhombic, oS16
Ama2, No. 40
Hazards
NFPA 704 (fire diamond)
NFPA 704 four-colored diamondHealth 3: Short exposure could cause serious temporary or residual injury. E.g. chlorine gasFlammability 0: Will not burn. E.g. waterInstability 0: Normally stable, even under fire exposure conditions, and is not reactive with water. E.g. liquid nitrogenSpecial hazards (white): no code
3
0
0
Lethal dose or concentration (LD, LC):
100 mg/kg
NIOSH (US health exposure limits):
PEL (Permissible)
 TWA 0.5 mg/m3 (as Sb)[1]
REL (Recommended)
 TWA 0.5 mg/m3 (as Sb)[1]
Related compounds
Related compounds
 antimony pentafluoride, antimony trichloride
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
☒N verify (what is checkY☒N ?)

Antimony trifluoride is the inorganic compound with the formula SbF3. Sometimes called Swarts' reagent, it is one of two principal fluorides of antimony, the other being SbF5. It appears as a white solid. As well as some industrial applications,[2] it is used as a reagent in inorganic and organofluorine chemistry.

Preparation and structure

In solid SbF3, the Sb centres have octahedral molecular geometry and are linked by bridging fluoride ligands. Three Sb–F bonds are short (192 pm) and three are long (261 pm). Because it is a polymer, SbF3 is far less volatile than related compounds AsF3 and SbCl3.[3]

SbF3 is prepared by treating antimony trioxide with hydrogen fluoride:[4]

Sb2O3 + 6 HF → 2 SbF3 + 3 H2O

The compound is a mild Lewis acid, hydrolyzing slowly in water. With fluorine, it is oxidized to give antimony pentafluoride.

SbF3 + F2 → SbF5

Applications

It is used as a fluorination reagent in organic chemistry.[5] This application was reported by the Belgian chemist Frédéric Jean Edmond Swarts in 1892,[6] who demonstrated its usefulness for converting chloride compounds to fluorides. The method involved treatment with antimony trifluoride with chlorine or with antimony pentachloride to give the active species antimony trifluorodichloride (SbCl2F3). This compound can also be produced in bulk.[7] The Swarts reaction is generally applied to the synthesis of organofluorine compounds, but experiments have been performed using silanes.[8] It was once used for the industrial production of freon. Other fluorine-containing Lewis acids serve as fluorinating agents in conjunction with hydrogen fluoride.

SbF3 is used in dyeing and in pottery, to make ceramic enamels and glazes.

Safety

The lethal minimum dose (guinea pig, oral) is 100 mg/kg.[9]

References

  1. ^ a b NIOSH Pocket Guide to Chemical Hazards. "#0036". National Institute for Occupational Safety and Health (NIOSH).
  2. ^ Sabina C. Grund, Kunibert Hanusch, Hans J. Breunig, Hans Uwe Wolf "Antimony and Antimony Compounds" in Ullmann's Encyclopedia of Industrial Chemistry, 2006, Wiley-VCH, Weinheim. doi:10.1002/14356007.a03_055.pub2
  3. ^ Greenwood, Norman N.; Earnshaw, Alan (1997). Chemistry of the Elements (2nd ed.). Butterworth-Heinemann. ISBN 978-0-08-037941-8.
  4. ^ Handbook of Preparative Inorganic Chemistry, 2nd Ed. Edited by G. Brauer, Academic Press, 1963, NY. Vol. 1. p. 199.
  5. ^ Tariq Mahmood and Charles B. Lindahl Fluorine Compounds, Inorganic, Antimony in Kirk‑Othmer Encyclopedia of Chemical Technology.doi:10.1002/0471238961.0114200913010813.a01
  6. ^ Swarts (1892). Acad. Roy. Belg. 3 (24): 474.{{cite journal}}: CS1 maint: untitled periodical (link)
  7. ^ US 4438088 
  8. ^ Booth, Harold Simmons; Suttle, John Francis (1946). "IV. The Preparation and Fluorination of Dimethyl and Trimethyl Chlorosilanes". J. Am. Chem. Soc. 68 (12): 2658–2660. doi:10.1021/ja01216a072.
  9. ^ Sabina C. Grund, Kunibert Hanusch, Hans J. Breunig, Hans Uwe Wolf “Antimony and Antimony Compounds” in Ullmann's Encyclopedia of Industrial Chemistry 2006, Wiley-VCH, Weinheim. doi:10.1002/14356007.a03_055.pub2