PROFILPELAJAR.COM

Specifications
Specifications
Configuration:;
• Whyte	4-8-2
• UIC	2'D1'h3g
Gauge	4 ft 8+1⁄2 in (1,435 mm) standard gauge
Driver dia.	5 ft 0 in (1,524 mm)
Adhesive weight	212,000 lb (96,162 kg; 96 t)
Loco weight	311,000 lb (141,067 kg; 141 t)
Firebox:
• Grate area	65 sq ft (6.04 m2)
Boiler pressure	200 psi (1.38 MPa)
Heating surface	3,390 sq ft (314.94 m2)
Superheater:;
• Heating area	775 sq ft (72.00 m2)
Cylinders	Three
Cylinder size	21.5 in × 28 in; (546 mm × 711 mm)
Valve gear	Outside: Walschaerts. Derived (middle): Rack and pinion

Type and origin
Type and origin
Power type	Steam
Builder	Eveleigh Railway Workshops (11); Cardiff Locomotive Workshops (2)
Total produced	13

New South Wales D58 class
New South Wales D58 class
	Class D58 Locomotive
Power type
Type and origin
Power type	Steam
Builder	Eveleigh Railway Workshops (11); Cardiff Locomotive Workshops (2)
Total produced	13
Configuration:;
Specifications
Configuration:;
• Whyte	4-8-2
• UIC	2'D1'h3g
Gauge	4 ft 8+1⁄2 in (1,435 mm) standard gauge
Driver dia.	5 ft 0 in (1,524 mm)
Adhesive weight	212,000 lb (96,162 kg; 96 t)
Loco weight	311,000 lb (141,067 kg; 141 t)
Firebox:
• Grate area	65 sq ft (6.04 m2)
Boiler pressure	200 psi (1.38 MPa)
Heating surface	3,390 sq ft (314.94 m2)
Superheater:;
• Heating area	775 sq ft (72.00 m2)
Cylinders	Three
Cylinder size	21.5 in × 28 in; (546 mm × 711 mm)
Valve gear	Outside: Walschaerts. Derived (middle): Rack and pinion
Tractive effort
Performance figures
Tractive effort	55,008 lbf (244.7 kN)
Factor of adh.	3.84
Operators
Career
Operators	New South Wales Government Railways
Class	D58
Numbers	5801–5813
Disposition	All scrapped, with exceptions to some tenders.

The D58 class was a class of steam locomotives built by the New South Wales Government Railways in Australia. They were built with the 4-8-2 wheel arrangement.

Design

In 1943, approval was given for the New South Wales Government Railways Workshops to build 25 freight locomotives. The design was a modified version of the 57 class. The main alterations were the use of a rack and pinion valve gear^[1] in lieu of the Gresley 2:1 conjugated valve gear for the middle cylinder and the use of smaller cylinders to enable the locomotives to run to on the Main North line to Broadmeadow, a route which had a tighter loading gauge. They also used a Woodard divided drive of twin coupling rods between the second and third driving wheels. A valance was fitted over the valve gear on the front platform.^[2] Similarly to the earlier D57 class and the later AD60 class, the 58 class were fitted with a mechanical stoker to feed the large firebox

Construction

Eveleigh Railway Workshops built 11 locomotives and Cardiff Locomotive Workshops with two. The first entered service in March 1950. The decision to move to diesel power saw only 13 locomotives completed.^[2]

Operations

Whilst the derived rack and pinion valve gear appeared superior in theory, in practice it required more maintenance and lubrication. The smaller diameter cylinders of the 58 class (21.1/2") compared to the earlier 57 class (23.1/4") demanded a later cut-off and thus used more steam. This could cause the locomotives to be uneconomical in the use of coal and water when compared with the 57 class, but the 58's longer valve travel ameliorated this objection if driven as designed to be so. Despite the design being made to enable use on the Main Northern line from Sydney to Broadmeadow, few journeys were ever made on this route. They mainly were used on the Main Western line to Lithgow and in a limited capacity on the Main South line to Junee.^[2]^[3]

After a very short service life, the entire class had been withdrawn by July 1957 and were all cut up by March 1964. Some parts were recovered and used on 57 class locomotives. There are no surviving examples, however the tender of 5808 lies near Canberra station as an old fuel tank for a Canberra-based diesel shunter (now disused). Some 58 class tenders saw further use as water tankers around New South Wales. One is at the Dorrigo Steam Railway and Museum.^[3]^[4]

References

^ Slee, David E (January 2000). "D57 and D58 Classes—Design Differences and Power Comparisons". Australian Railway Historical Society Bulletin: 3–19.
^ ^a ^b ^c Grunbach, Alex (1989). A Compendium of New South Wales Steam Locomotives. Sydney: Australian Railway Historical Society, NSW Division. pp. 232–235. ISBN 0-909650-27-6.
^ ^a ^b Oberg, Leon (1984). Locomotives of Australia 1850's - 1980's. Frenchs Forest: Reed Books. pp. 168–170. ISBN 0-730100-05-7.
^ Wright, H (July 1964). "The Last of the 58-Class 'Mountain' Locomotives". Australian Railway Historical Society Bulletin: 130–132.