A failure of the craft's propulsion system resulted in Lunar Flashlight being unable to enter orbit around the Moon and NASA terminated the mission on May 12, 2023.[9][10] The spacecraft has since been abandoned in a solar orbit after flying by Earth on May 17 for a coincidental gravity assist.
History
NASA's Lunar Crater Observation and Sensing Satellite (LCROSS), the Lunar Reconnaissance Orbiter (LRO) and India's Chandrayaan-1 lunar orbiters and other missions discovered in 2009 both water (H2O) and hydroxyl (—OH−) deposits at high latitudes on the lunar surface, indicating the presence of trace amounts of adsorbed or bound water are present.[3] These missions suggest that there might be enough ice water at polar regions to be used by future landed missions,[5][6] but the distribution is difficult to reconcile with thermal maps.[3]
Lunar prospecting missions are intended to pave the way toward incorporating use of space resources into mission architectures. NASA's planning for eventual Human mission to Mars depends on tapping the local natural resources to make oxygen and propellant for launching the return ship back to Earth, and a lunar precursor mission is a convenient location to test such in situ resource utilization (ISRU) technology.[11]
In its original conception, the Lunar Flashlight spacecraft would have been a 6U CubeSat format or bus propelled by an 80 m2solar sail that would also have functioned as reflector to illuminate some selected permanently shadowed areas on the Moon,[5] while an onboard infrared spectrometer measured the reflected spectrum diagnostic of surface compositional mix among rock/dust, regolith, water ice, CO2, methane ice (CH4), and possibly ammonia ice (NH3).[3][2][5] The illuminated spot would have been about 400 m (1,300 ft) in diameter, reflected from an altitude of 20 km (12 mi).
In the final design, the Lunar Flashlight spacecraft includes two sets of solar arrays. One set delivered by Blue Canyon Technologies (BCT) which deploys upon release from the dispenser and another delivered by MMA which use a burnwire deployment mechanism. The Command and Data Handling is provided via the JPL-developed Sphinx processor with flight software written using the JPL-developed FPrime software framework. The on-board radio is an Iris radio developed by JPL and build by Space Dynamics Laboratory. The attitude determination and control system (ADCS) for the spacecraft is provided by a BCT XACT-50. The spacecraft includes a chemical propulsion system to provide the impulse needed for Lunar Orbital Insertion (LOI). This propulsion system was designed and built by Georgia Tech’s Glenn Lightsey Research Group in collaboration with the NASA Marshall Space Flight Center. Finally, the science instrument payload is a compact Short Wave Infrared (SWIR) Laser reflectometer.[13]
Overview and objectives
The goal of Lunar Flashlight is to determine the presence or absence of exposed water ice and its physical state, and map its concentration at the 1-2 kilometer scale within the permanently shadowed regions of the lunar south pole.[4][14][15] The mission will be one of the first CubeSats to reach the Moon, and the first mission to use lasers to look for water ice.[1] Any polar volatile data collected by Lunar Flashlight could then ensure the most appropriate landing sites for a more expensive rover to perform in situ measurements and chemical analyses.[5] The spacecraft will maneuver to its lunar polar orbit and use its near infraredlasers to shine light into the shaded polar regions, while the on-board spectrometer measures surface reflection and composition.[1]Barbara Cohen from the NASA Goddard Space Flight Center is the principal investigator.[4]
Scientific payload
Lunar Flashlight after integration
The proposed payload on this nanosatellite is an infrared spectrometer, consisting of a lens, dichroic beam splitters and multiple single-element detectors. It occupies 2 of the 6 modules of the 6U CubeSat bus.[3] The attitude control system (Blue Canyon Technologies' XACT-50), command and data handling, and power systems will occupy 1.5U; the Iris telecom system will occupy 0.5U.[2]
The Lunar Flashlight spacecraft was ejected from the Falcon 9 second stage after trans-lunar injection, after which it used a Sun sensor and solar panels to power the 3-axes reaction wheels. It also featured a chemical monopropellant propulsion and orientation system built by the Georgia Tech Space System Design Laboratory. The propulsion system occupied 3U of volume including 2 kg of AF-M315E monopropellant,[16] a less toxic HAN-based monopropellant being used in lieu of hydrazine. The intricate propellant management unit was fabricated using additive manufacturing.[16][17]
Thruster problems
During the first few days of flight (December 2022), it was found that 3 of the 4 thrusters were underperforming. As of January 2023 the mission team was working to remedy the problem.[18] Limited success was achieved with the other 3 thrusters by May 2023.[19]
Orbit
The spacecraft was planned to be the second to use a near-rectilinear halo orbit, the first being the CAPSTONE mission.[17] The original concept proposed a trajectory that would target multiple lunar flybys, and possibly include an Earth gravity assist; it would have been captured into a lunar polar orbit one or two months after launch, depending on the selected trajectory.[3]
^ abcdef"Lunar Flashlight". Solar System Exploration Research Virtual Institute (SSERVI). NASA. 2015. Retrieved 11 March 2021. This article incorporates text from this source, which is in the public domain.
Launches are separated by dots ( • ), payloads by commas ( , ), multiple names for the same satellite by slashes ( / ). Crewed flights are underlined. Launch failures are marked with the † sign. Payloads deployed from other spacecraft are (enclosed in parentheses).
