The structure resembles a cross-section of a swimming pool, essentially two concave ramps (or quarter-pipes), topped by copings and decks, facing each other across a flat transition, also known as a tranny.[1] Originally half-pipes were half sections of a large diameter pipe. Since the 1980s, half-pipes contain an extended flat bottom between the quarter-pipes. The original style half-pipes are no longer built. Flat ground provides time to regain balance after landing and more time to prepare for the next trick.
Half-pipe diagram
Half-pipe applications include leisure recreation, skills development, competitive training, amateur and professional competition, demonstrations, and as an adjunct to other types of skills training.
A skilled athlete can perform in a half-pipe for an extended period of time by pumping to attain extreme speeds with relatively little effort. Large (high amplitude) half-pipes make possible many of the aerial tricks in BMX, skating and skateboarding.
For winter sports such as freestyle skiing and snowboarding, a half-pipe can be dug out of the ground or snow perhaps combined with snow buildup. The plane of the transition is oriented downhill at a slight grade to allow riders to use gravity to develop speed and facilitate drainage of melt. In the absence of snow, dug out half-pipes can be used by dirt-boarders, motorcyclists, and mountain bikers.
Performance in a half-pipe has been rapidly increasing over recent years. The current limit performed by a top-level athlete for a rotational trick in a half-pipe is 1440 degrees (four full 360 degree rotations). In top level competitions, rotation is generally limited to emphasize style and flow.
Origin
In the early 1970s, swimming pools were used by skateboarders in a manner similar to surfing ocean waves. In 1975, some teenagers from Encinitas, California, and other northern San Diego County communities began using 7.3-meter-diameter (24 ft) water pipes in the central Arizona desert associated with the Central Arizona Project, a federal public works project to divert water from the Colorado River to the city of Phoenix. Tom Stewart, one of these young California skateboarders,[2] looked for a more convenient location to have a similar skateboarding experience. Stewart consulted with his brother Mike, an architect, on how to build a ramp that resembled the Arizona pipes. With his brother's plans in hand, Tom built a wood frame half-pipe in the front yard of his house in Encinitas.
In a few days, the press had gotten word about Tom's creation and contacted him directly. Tom then went on to create Rampage, Inc. and began selling blueprints for his half-pipe design.[2] About five months later, Skateboarder magazine featured both Tom Stewart and Rampage.
Design
Mini ramp (no vertical)
The character of a half-pipe depends on the relationship between four attributes: most importantly, the transition radius and the height, and less so, the degree of flat bottom and width. Extra width allows for longer slides and grinds. The flat bottom, while valued for recovery time, serves no purpose if it is longer than it needs to be.[3]
Thus, it is the ratio between height and transition radius that determines the personality of a given ramp, because the ratio determines the angle of the lip.[4]
On half-pipes which are less than vertical, the height, typically between 50% and 75% of the radius, profoundly affects the ride up to and from the lip, and the speed at which tricks must be executed. Ramps near or below 0.91 m (3 ft) of height sometimes fall below 50% of the height of their radius. Technical skaters use them for advanced flip tricks and spin maneuvers. Smaller transitions that maintain the steepness of their larger counterparts are commonly found in pools made for skating and in custom mini ramps. The difficulty of technical tricks is increased with the steepness, but the feeling of dropping in from the coping is preserved.
The standard design in the construction of ramps is to use a constant radius in transitions:
Most of the ramps are built with a quarter circle of constant radius for easy construction, and this method is tried and true. But some of the best ramps are not constant radius but a roughly elliptical with somewhat less final vert (vertical).
The design is supposed to allow for easy big air with return still on the curve and less danger of landing on the flat ("bottoming out").
Construction of a cycloid
Mathematics
A cycloid profile will theoretically give the fastest half-pipe if friction is neglected. It is then called a brachistochrone curve. Such a curve in its pure form has infinitely short verts and is π times as wide as it is high.
Skateboarding, freestyle BMX, scootering, and aggressive inline skating
Frame and support for skateboard, BMX, and vert skating half-pipes frequently consist of a 2×6×8" lumber (actual 38 × 140 × 184 mm) framework sheathed in plywood finished with sheets of masonite or Skatelite. Also, a metal frame finished in wood or metal is sometimes used.[citation needed]
Most commercial and contest ramps are surfaced by attaching sheets of some form of masonite to a frame. Many private ramps are surfaced in the same manner but may use plywood instead of masonite as surface material. Some ramps are constructed by spot-welding sheet metal to the frame, resulting in a fastener-free surface. Recent developments in technology have produced various versions of improved masonite substances such as Skatelite, RampArmor, and HARD-Nox.[5] These ramp surfaces are far more expensive than traditional materials.
Channels, extensions, and roll-ins are the basic ways to customize a ramp. Sometimes a section of the platform is cut away to form a roll-in and a channel to allow skaters to commence a ride without dropping in and perform tricks over the gap. Extensions are permanent or temporary additions to the height of one section of the ramp that can make riding more challenging.
Creating a spine ramp is another variation of the half-pipe. A spine ramp is basically two quarter pipes connected at the vertical edge.
Half-pipes in snow were originally done in large part by hand or with heavy machinery. Pipes were cut into snow using an apparatus similar to a grain auger. Colorado farmer Doug Waugh created the Pipe Dragon used in both the 1998 and 2002 Winter Olympics.[6] One current method of half-pipe cutting is by use of a Zaugg Pipe Monster, which uses five snow-cutting edges to create an elliptical shape that is purportedly safer and allows the rider to gain more speed.[7]
In winter sports, a 6.7 m (22 ft) halfpipe is called a superpipe. The tallest snow superpipe in the world (as of 2021[update]) is located near Laax, Switzerland.[8] With a height of 6.90 m (22.6 ft), this halfpipe has held the world record since the 2014–2015 season, and regularly hosts the LAAX Open.
.jpg)
