The 3⁄4‑ton WC-54 was designed as successor to the previous 1/2-ton, 4×4, G-505 models WC-9, WC-18, and WC-27 Dodge Ambulance trucks.[2]
Although based on the 3/4-ton Dodge "Beep" chassis, which front and rear axles featured wider tracks of 64+3⁄4 in (1.64 m), the 3/4-ton ambulance versions retained a longer wheelbase, very close to that of the previous half-tonners, as well as somewhat rounded, upward sloping nose sheetmetal, instead of the fully horizontal, flat and wider engine-cover of the main 3⁄4‑ton redesigned WC-models.[3] The WC-54s also had adjusted suspension to make their ride softer.
The body of the 1/2-ton WC-27 (pictured) was largely carried over on the 3/4-ton WC‑54.]]
The closed sheet-metal body was made by Wayne Body works. It had room for a driver and four to seven patients plus a medic. If the fold-away bunk stretchers were used, four patients could be transported lying down.[2]
Because of its intended role, the WC-54 featured a large matrix cab heater fitted on the inner firewall, providing comfort for patients and crew. It was fitted with a foldaway step to its rear to allow easier access for stretcher bearers and injured personnel. Early models featured a stuck out fuel filler cap which was changed to a recessed one in the later model, a modification that was retrofitted to some early model trucks.
From 1942 to 1945, total production of the 3/4-ton Dodge WC-series was some 255,000. Of these, 29,502 were ambulances — 26,002 WC‑54 and 3,500 WC-64 KD models.[1][4] The vehicles were supplied under US government contracts W398-QM-11420 (850 units), W398-QM-11422 (9,945 units), DAW398-QM-448 (16 units), W398-QM-13596 (410 units) and W374-ORD-2864 (11,636 units).[2]
WC-64 Knock-Down
Virtually unchanged for three years, apart from minor technical tweaks, in 1945 it was replaced by a new knock-down body design, the WC‑64(KD). Based on essentially the same chassis as the WC‑54, the rear ambulance boxes were now split in two major sections: lower and upper, designed primarily to increase the number of vehicles that could be shipped at the same time. The lower part of the ambulance body was attached to the chassis at the factory, while the upper box consisted of flat panels, shipped in crates for installation in the field.[5] Only produced in 1945, just 3,500 of these were made before the war ended.[1] Other model changes made the WC‑64 more similar to the WC‑51: the factory-fitted lower ambulance-box outwardly resembles that of the WC‑51's rear bed boxes, though the WC‑64 is of course longer; and the flat instead of sloped hood, and spare wheel placement are now also like on a WC‑51.
The "knocked-down" condition was so much more space-efficient that two ambulances could now be stacked, and shipped in the same space that would previously hold only one conventional WC‑54 ambulance. Additionally, the reduced size also allowed air transportation of the vehicle.[6]
^ abcChief of Ordnance Office; Military Vehicle Preservation Association, eds. (2010). Summary Report of Acceptances, Tank-Automotive Materiel, 1940-1945 (Revision). Detroit: U.S. Army Service Forces, Office: Chief of Ordnance-Detroit, Production Division, Requirements and Progress Branch (published December 1945). p. 62.
TM 9-2800 Standard Military Motor Vehicles, 1 sept. 1943, pages 356–357
TM 9-2800 Military vehicles dated Oct. 1947
TM 9-808 3/4-ton Dodge truck dated Jan. 1944
SNL G502
SNL G657 Dodge master parts book
Classic Military Vehicles (magazine). "Dodge WC54 Ambulance." Classic Military Vehicles Number 4, September 2001. Cudham, Kent, UK: Kelsey Publishing Limited.
Classic Military Vehicles (magazine). "Dodge WC54 Ambulance." Classic Military Vehicles Number 11, April 2002.Cudham, Kent, UK: Kelsey Publishing Limited.
External links
Wikimedia Commons has media related to Dodge WC-54.